Zebra · 2.25 × 1.25 in
How to print FNSKU labels on a Zebra GK420d (2.25 × 1.25 in)
Set the paper size to 2.25 × 1.25 in (57 × 32 mm) in the Zebra GK420d driver, print at Scale 100% with margins set to None, and use a PDF whose page is exactly one 2.25 × 1.25 in label. Prepline turns Amazon’s label PDF into that file in your browser, with the barcode rebuilt for the printer’s dots, and remembers your printer’s offset after one test label.
The settings
| Setting | Zebra GK420d, 2.25 × 1.25 in |
|---|---|
| Paper size | 2.25 × 1.25 in (57 × 32 mm) |
| Scale | 100% (Actual size). Never “Fit to page”. |
| Margins | None |
| Orientation | Landscape |
| Headers and footers | Off |
| Media type | Labels with gaps (web / gap sensing) |
| Print resolution | 203 dpi, direct thermal |
2.25 × 1.25 in on the GK420d gives a little more room than 2 × 1: the title gets a full line and the bars stay at 2 dots. Make it a Stock in the ZDesigner driver and pick that Stock in the print dialog.
Set up the Zebra GK420d once
- Add the paper size. ZDesigner driver: Printing Preferences → Page Setup → Stocks → New, enter the size; set Media Type to “Labels with gaps”.
- Teach it the label. GK/GX: hold Feed until the light flashes twice, then let go to calibrate. ZD: hold Pause + Cancel for 2 seconds.
- Make the PDF. Drop Seller Central’s label PDF into Prepline (any layout, including the 30-up sheet), pick Zebra GK420d and 2.25 × 1.25 in. Each label lands on its own page of exactly that size.
- Print one test label and scan it with your phone. If it’s off by a millimetre, measure the two gaps on Prepline’s test label once and it’s fixed for good.
When it goes wrong
The sides are cut off
The page is bigger than the label. Seller Central’s PDF is a Letter page (or a 2.625 in sheet label), and the printer crops whatever doesn’t fit. Use a PDF whose page is exactly 2.25 × 1.25 in, print at Scale 100%, and keep the bars inside a 2 mm margin.
Two labels per sticker, or the label is tiny
The print dialog is shrinking a big page to fit, usually “Fit to page” or “Scale to fit”. Set Scale to 100% (Actual size) and choose 2.25 × 1.25 in as the paper size, not Letter.
A blank label between every label
The printer thinks the labels are longer than they are. GK/GX: hold Feed until the light flashes twice, then let go to calibrate. ZD: hold Pause + Cancel for 2 seconds. Also check that the paper height in the driver is 1.25 in, not 6 in.
Everything is shifted a millimetre or two
Every printer feeds a little differently. Print Prepline’s test label (a frame 2 mm inside each edge), measure the left and top gaps, and Prepline moves all future labels by the difference. Saved for this printer.
The barcode won’t scan
Thin bars smeared by heat, or bars squeezed by scaling. Prepline draws every bar as whole printer dots (203 dpi), so check that Scale is 100%, lower the darkness one step if bars look fat, and scan the test label with a phone before the full run.
Questions
What paper size do I pick for 2.25 × 1.25 in labels on a Zebra GK420d?
2.25 × 1.25 in (57 × 32 mm). Choose it in the print dialog (or add it in the printer driver first), with Scale 100% and margins None.
Is 2.25 × 1.25 in big enough for Amazon FNSKU labels?
Yes. Amazon accepts item labels from 1 × 2 in up to 2 × 3 in, and 2.25 × 1.25 in (57 × 32 mm) is inside that range.
Do I need special software for the Zebra GK420d?
Only its normal driver. Prepline runs in the browser and gives you a PDF with the right page size, so any PDF viewer can print it.
Updated November 9, 2026